Categories

Information

Home| JeffTron Switch Brake (Microswitch replacement MOSFET)

Manufactured by: Jefftron

JeffTron Switch Brake (Microswitch replacement MOSFET) (JT-BRK-S4)

Manufactured by: Jefftron

JeffTron Switch Brake (Microswitch replacement MOSFET) (JT-BRK-S4)

Weight: 0.02 lb

Model: JT-BRK-S4

$25.00
$25.00
10
In Stock
product details

Professionally made mosfet with active braking, which can be disabled by removing red jumper.

Device is designed to replace microswitch in the specific gearbox V2.
There is no modification needed.

In semi fire mode piston isn't partially stretched, spring is fully released, parts in mechabox aren't under strain and nozzle locks hop-up chamber in greater part (depends on ROF).

Active break solves multiple shots in semi mode with weapons with very high rate of fire (ROF).

Device increases gun rate of fire and battery holds longer, than with basic wiring.

switch brake postion

SPECIFICATIONS:
- Easy installation inside the gearbox version 2, which replace microswitch
- Devices without wires, you can use max. 1,5qmm (AWG16) power wires and 0,5qmm (AWG20) signal wires
- Suitable for service center, if you are not familiar with soldering to the circuit board, choose device with wiring and accessories
- Disable active braking by unplugging red jumper, when you gun has Rate of fire under 20bb/s, otherwise it could lock up trigger on SEMI due too low gear speed.
- Motor will be under less stress without active braking.
- Designed for spring up to M160 (equivalent for current 75A single shot fire or 25A burst fire for max. 30s)
- Specified for common batteries up to 17V (Ni-xx 8.4 - 12V, lipol 7.4 - 14.8V)
- Active braking uses the excess energy from the motor to stop it. The braking effect is the most powerful with high torgue motor
- In auto fire mode piston stops in random position due the mechabox design
- For right function is necessary to have a functional gearbox cut off lever, selector plate, reverse latch, trigger and trigger block, as it has the standard gearbox

DEVICE INSTRUCTIONS: you can download installation manual in English here [1.27 MB]

PACKING: device and installation manual in English

WARNING: Installation of this device leave to expert, who could solder and disassemble airsoft gun. Never user soldering gun!

The device is not compatible with the PTS masada, where the trigger operation is reversed

WIRING CONNECTION INTO THE GUN:

switch_brake

 

tabulka_produktu

ASN Plus is our partner for PCB design, electronics production and development, embedded software development, software and apps development.

product details

Professionally made mosfet with active braking, which can be disabled by removing red jumper.

Device is designed to replace microswitch in the specific gearbox V2.
There is no modification needed.

In semi fire mode piston isn't partially stretched, spring is fully released, parts in mechabox aren't under strain and nozzle locks hop-up chamber in greater part (depends on ROF).

Active break solves multiple shots in semi mode with weapons with very high rate of fire (ROF).

Device increases gun rate of fire and battery holds longer, than with basic wiring.

switch brake postion

SPECIFICATIONS:
- Easy installation inside the gearbox version 2, which replace microswitch
- Devices without wires, you can use max. 1,5qmm (AWG16) power wires and 0,5qmm (AWG20) signal wires
- Suitable for service center, if you are not familiar with soldering to the circuit board, choose device with wiring and accessories
- Disable active braking by unplugging red jumper, when you gun has Rate of fire under 20bb/s, otherwise it could lock up trigger on SEMI due too low gear speed.
- Motor will be under less stress without active braking.
- Designed for spring up to M160 (equivalent for current 75A single shot fire or 25A burst fire for max. 30s)
- Specified for common batteries up to 17V (Ni-xx 8.4 - 12V, lipol 7.4 - 14.8V)
- Active braking uses the excess energy from the motor to stop it. The braking effect is the most powerful with high torgue motor
- In auto fire mode piston stops in random position due the mechabox design
- For right function is necessary to have a functional gearbox cut off lever, selector plate, reverse latch, trigger and trigger block, as it has the standard gearbox

DEVICE INSTRUCTIONS: you can download installation manual in English here [1.27 MB]

PACKING: device and installation manual in English

WARNING: Installation of this device leave to expert, who could solder and disassemble airsoft gun. Never user soldering gun!

The device is not compatible with the PTS masada, where the trigger operation is reversed

WIRING CONNECTION INTO THE GUN:

switch_brake

 

tabulka_produktu

ASN Plus is our partner for PCB design, electronics production and development, embedded software development, software and apps development.

Customer Reviews

Be the first to write a review
0%
(0)
0%
(0)
0%
(0)
0%
(0)
0%
(0)

Categories

Information

manufacturers

4UADACETECHAction ArmyActionSportGa...Airsoft Innov...Airsoft MutationAirsoft PartsAlphaWireAztech Innova...BioshotBRILL ARMORYBullgearCHEMIS CYMAda Vinci AirsoftDream ArmyEagle6 AirsoftEcho 1ElementElite ForceEmei Landarms...EPeS Airsoft Field Limit T...FPS SoftairGATE ElectronicsGuarderGungineer Air...JefftronLambda AirsoftLaylaxLCTLonexMaekiiiMancraft AirsoftMaple Airsoft...Maple LeafMaxxModifyNorthern Hurr...Orga AirsoftParagon ArmoryPDIPerun AirsoftPolarStar Air...Professional ...Retro ARMSRocket AirsoftSapporo Preci...ScatterplotSHSSiegetek Conc...Silent Indust...SlongSolinkSparkLabsSpring-TekSuper LubeSuper ShooterT238TechTTruSight Airs...Unicorn AirsoftW.S. Deans Co.Warhead Indus...ZCI